WD-1201M-DIN(V3)-I/O

Brief introduction

DIN Rail Industrial PLC Ethernet Bridge WD-1201M-DIN(V3)-I/O is a powerline telecommunication product which developed by WonderTek Technology (KunShan) Co.,LTD., it supports HomePlugAV2 protocol. it has been widely used in railway, mineral, industrial communication, airport, subway, coal mine, intelligent storage, industrial automation control, automatic garage and other wired or sliding contact line and many other sites.

1.1 Highlight

1.1.1 Technical parameters

Support HomePlug/HomePlugAV2.
Industrial DIN rail style installation.
Actual bandwidth up to 550Mbps.
The maximum transfer distance up to 500 meters.
Self-adapt the rate.
One Domain Master can manage 127pcs End Point.
Support I/O in or out

1.1.2 Manageability

Support Remote Firmware update(TR069).
802.3D Ethernet Bridge.
802.1Q VLAN.
Quality of Service(QoS) .
IGMO(IPv4)Snooping&MLD(IPv6)Snooping.

1.1.3Operating environment

Working temperature: -20℃-80℃.
Operating humidity: 10%-85% no condense.
Storage humidity:5%-90% no condense.

1.1.4 Design standards

IEC 60529 IEC 50022 IEC 60068-2-6 MIL-STD-810G HomePlugAV

Specification
Model	WD-1201M-DIN(V3)-I/O
Interface	1LAN 10/100/1000Base-TX self adaption RJ45，1 Power interface 1* Four- terminal I/O input/output port
LED display light	Ethernet PLC Power
Transfer frequency	2-68MHz
Protocol（PHY）	IEEE802.3，IEEE802.3x, IEEE802.3u HomePlugAV2
Security	128-AES
Transfer rate（PHY）	1200Mbps
Number of each group	128
Modulation	OFDM
Effective transfer rate	TCP/IP 550Mbps
	802.1D Ethernet Bridge
	802.1Q VLAN
	Quality of Service(QoS)
Operating temperature	-20℃-80℃
Size	1209045mm（L×W×H）
Working voltage	AC85-520V
Weight	0.30kg
Operating environment	Operating humidity:10%-85% (no condense)
Operating environment	Storage humidity: 5%-90%(no condense)
Certification	FCC、CE class B,WEEE,RoHS

1.2 Features

(1) Packet loss：≤0.1%（100M,load 70%）.
(2) Support 7*24 hours all weather operation.
(3) Hardware watch dog function.
(4) PING≤2MS.

1.3 Immunity of ESD

The testing voltage which the device should be beared: ±6kV direct Discharge, ±8kV air discharge.
Discharge number in Each sensitive testing point: Plus-n-Minus 10 times each,
Every time the discharge interval is 1 s, according to B/T 17626.2-2006.

1.4 Immunity of electrical fast transient impulse group(Common mode)

The testing voltage which the device should be beared:
between the power supply voltage port and ground: ±2.0kV;
between signal circuit and ground: ±1.0kV;
repetition frequency: 5KHz, test duration: 1 min/ time;
testing times: Plus-n-Minus 5 times each.
According to GB/T 17626.4-2008.

1.5 Anti interference of surge impact

The testing voltage which the device should be beared: ±2kV;
The interval of continuous impulses: 1min/time;
Test number: Plus-n-Minus 5 times each.
According to GB/T 17626.5-2008.(protection: all models protection and varistor series of discharge tube type)

1.6 Anti- vibration

Meet the demand of MX3 in TB1433(0-200Hz,2g acceleration, maximum amplitude 7mm), interface with no loose, device with no Sealing off and drop in the test.